dcc_mm2_shield_r5d
差分
このページの2つのバージョン間の差分を表示します。
両方とも前のリビジョン前のリビジョン次のリビジョン | 前のリビジョン次のリビジョン両方とも次のリビジョン | ||
dcc_mm2_shield_r5d [2016/05/15 21:01] – yaasan | dcc_mm2_shield_r5d [2016/12/01 16:45] – [DCC/MM2 shield] yaasan | ||
---|---|---|---|
行 1: | 行 1: | ||
- | ====== DCC/MM2 shield | + | ====== DCC/MM shield ====== |
- | DCC/MM2 Shield | + | DCC/MM Shield is a command station board to control DCC and Marklin locomotives and turnouts. R5D or later version supports S88 interface function which detects train exists.\\ |
- | DCC/ | + | DCC/ |
Old version page is [[http:// | Old version page is [[http:// | ||
旧バージョンのページは[[http:// | 旧バージョンのページは[[http:// | ||
- | ===== Outline ===== | + | ===== 概要 / Outline ===== |
* デジタル鉄道模型のデファクトスタンダードであるDCCとMarklin Motorola2(MM2)の搭載車両とポイントに対応。mfx機関車はMM2モードで使用可能。 | * デジタル鉄道模型のデファクトスタンダードであるDCCとMarklin Motorola2(MM2)の搭載車両とポイントに対応。mfx機関車はMM2モードで使用可能。 | ||
行 19: | 行 19: | ||
- | ===== PCB and assembly ===== | + | ===== 基板と組み立て例 / PCB and assembly ===== |
{{http:// | {{http:// | ||
行 31: | 行 31: | ||
{{: | {{: | ||
- | ===== Description hardware ===== | + | ===== ハードウェアの説明 / Description hardware ===== |
* RJ45 Connector is S88-N interface. You can connect S88 decoder, e.g. LDT's or the other third party products.\\ RJ45のコネクタはS88-Nインターフェースです。S88デコーダを接続できます。 | * RJ45 Connector is S88-N interface. You can connect S88 decoder, e.g. LDT's or the other third party products.\\ RJ45のコネクタはS88-Nインターフェースです。S88デコーダを接続できます。 | ||
* 2pin push-in terminal is output terminal connecting to main track.\\ 緑色のターミナルブロックはプッシュイン式で、線路に繋げるフィーダー線を接続できます。 | * 2pin push-in terminal is output terminal connecting to main track.\\ 緑色のターミナルブロックはプッシュイン式で、線路に繋げるフィーダー線を接続できます。 | ||
- | * Arduino UNO's DC jack\\ DCジャックは、Arduino UNOに装着されているものを使用します。 | + | * Arduino UNO's DC jack\\ DCジャックは、Arduino UNOに装着されているものを使用します。電源電圧は12Vです。ArduinoUNOの仕様に従ってください。 |
* USB connector at Arduino UNO board can connect to PC or Mac.\\ USBコネクタは、PCやMacに接続できます。 | * USB connector at Arduino UNO board can connect to PC or Mac.\\ USBコネクタは、PCやMacに接続できます。 | ||
* RUN LED turns on when DCC or MM2 signal is provided in the track. \\ RUN LEDは、線路にDCCやMM2信号が流されている場合に点灯します。 | * RUN LED turns on when DCC or MM2 signal is provided in the track. \\ RUN LEDは、線路にDCCやMM2信号が流されている場合に点灯します。 | ||
行 46: | 行 46: | ||
===== Instruction for soldering ===== | ===== Instruction for soldering ===== | ||
- | - 背の低い部品からはんだづけします。抵抗-> | + | - 背の低い部品からはんだづけします。抵抗-> |
- | - テスタで、VIN-GND, | + | - テスタで、VIN-GND, |
- | - Arduino UNOに装着して、ACアダプタを接続し、POWER LEDが点灯するか確認します。LEDが点灯しない場合、部品の接続不良またはショートが想定されます。 | + | - Arduino UNOに装着して、ACアダプタを接続し、POWER LEDが点灯するか確認します。LEDが点灯しない場合、部品の接続不良またはショートが想定されます。\\ Check Power LED after connecting DC power suppply and inserting to Arduino UNO. If LED turned off, check soldering. |
===== Instruction for use ===== | ===== Instruction for use ===== | ||
+ | |||
+ | 有志が、使用方法をまとめています。そちらも参照すると便利です。 | ||
+ | [[http:// | ||
- Arduino UNOにDCC/ | - Arduino UNOにDCC/ | ||
行 69: | 行 72: | ||
- Desktop Stationソフトウェアではなく、自分で自動運転やセンサと連動したオリジナルのソフトを作ることも出来ます。Arduinoでのソフトの作り方は、[[http:// | - Desktop Stationソフトウェアではなく、自分で自動運転やセンサと連動したオリジナルのソフトを作ることも出来ます。Arduinoでのソフトの作り方は、[[http:// | ||
+ | ※[[DSCore|DSCore specification]]のHexファイルも公開しております。自分で基板を作って材料費のみで自作も可能です。 | ||
===== User application / ユーザー事例 ===== | ===== User application / ユーザー事例 ===== |
dcc_mm2_shield_r5d.txt · 最終更新: 2017/10/11 07:52 by yaasan