smile_writer
差分
このページの2つのバージョン間の差分を表示します。
両方とも前のリビジョン前のリビジョン次のリビジョン | 前のリビジョン次のリビジョン両方とも次のリビジョン | ||
smile_writer [2015/07/05 23:25] – [Smile Writer] yaasan | smile_writer [2018/06/16 17:45] – [Smile Writer / スマイルライター] yaasan | ||
---|---|---|---|
行 1: | 行 1: | ||
- | ====== Smile Writer ====== | + | ====== Smile Writer |
- | スマイルライターは、[[DS Smile Decoder (DSdecR3)]]用の書き込み器具です。 | + | スマイルライターは、MP3デコーダ([[http:// |
- | ===== How to assemble Smile Programmer ===== | + | 旧版は[[SmileWriterV1|こちら]]です。 |
- | Cut the red line which is RESET line between ICSP and Reset button. After that, jumper D10 and RST as the following. | + | ===== 特長 ===== |
- | {{http:// | + | Arduino UNOに載せるタイプで、安定して書き込みが行えます。Arduino UNOには、Arduino ISPスケッチを書き込むことで、スマイルデコーダなどのType-A準拠のDCCデコーダにファームウェアを書き込みできます。価格は1800円(部品キット)です。 |
- | [[http:// | + | |
- | Insert Card edge connector and solder it. That's all! | + | {{http:// |
- | {{http:// | ||
- | [[http:// | ||
- | Smile Programmer | + | ===== 組み立て方 / How to assemble |
- | {{http:// | + | |
- | Programming Arduino sketch using Smile Writer\\ | + | LEDのみ極性があります。以下のように、LEDの方向に注意して半田付けしてください。 |
- | {{http:// | + | |
- | ===== Setup software for smile writer ===== | + | {{:: |
+ | 以下のように半田付けします。 | ||
+ | |||
+ | {{http:// | ||
+ | |||
+ | ===== ソフトの設定方法 / Setup software for smile writer ===== | ||
+ | |||
+ | 最初に、以下のようにスマイルライターをセットアップします。以下の手順は、最初に行うだけで良いです。\\ | ||
First time, you need to set up Smile Writer as the following. This following procedure does only once at first time. | First time, you need to set up Smile Writer as the following. This following procedure does only once at first time. | ||
- | - Check Serial port connected Smile Writer. You did not install CH340G driver, install it. You can download | + | - 予め、[[https://www.arduino.cc/en/Main/Software|Arduino IDEをダウンロード]]して下さい。1.6.x以降を推奨します。 |
- | - Run Arduino IDE. | + | - スマイルライターに接続されたシリアルポートを確認してください。もし、Arduino UNOのドライバをインストールしていない場合は、インストールしてください。 |
- | - Set board to Arduino | + | - Arduino IDEを起動してください。\\ |
- | - Open " | + | - Arduino IDEのボード設定及びマイコン設定はArduino UNOを選択してください。COMポートは認識されているボードに対応したものを選んでください。書き込み装置は、" |
- | - Upload it. | + | - ファイルメニューのスケッチの例から、" |
+ | - " | ||
+ | |||
+ | ===== 販売 ===== | ||
+ | |||
+ | [[https:// | ||
smile_writer.txt · 最終更新: 2018/09/09 09:26 by yaasan