smile_writer
差分
このページの2つのバージョン間の差分を表示します。
両方とも前のリビジョン前のリビジョン次のリビジョン | 前のリビジョン次のリビジョン両方とも次のリビジョン | ||
smile_writer [2016/01/17 17:31] – yaasan | smile_writer [2018/06/16 06:41] – yaasan | ||
---|---|---|---|
行 1: | 行 1: | ||
====== Smile Writer / スマイルライター ====== | ====== Smile Writer / スマイルライター ====== | ||
- | スマイルライターは、[[DS Smile Decoder (DSdecR3)]]用の書き込み器具です。 | + | スマイルライターは、[[DS Smile Decoder (DSdecR3)]]や、MP3デコーダ(なごでん)、スマイルファンクションデコーダ(DCC館)用の書き込み器具です。 |
+ | |||
+ | [[SmileWriterV1]] | ||
+ | |||
+ | 大きく2つの装置を提供しています。 | ||
+ | |||
+ | ===== 種類 ===== | ||
+ | |||
+ | ==== スマイルライター(単体動作タイプ) ==== | ||
+ | |||
+ | Arduino nano互換ボードを改造して安価に実現したタイプです。パターンカットや、ジャンパー、コネクタのピッチを曲げる作業が必要です。 | ||
+ | Arduino nanoには、Arduino ISPスケッチを書き込むことで、スマイルデコーダなどのType-A準拠のDCCデコーダにファームウェアを書き込みできます。価格は2000円(部品キット)です。 | ||
+ | |||
+ | {{http:// | ||
+ | |||
+ | |||
+ | ==== スマイルライタシールド(Arduino UNO子亀タイプ) ==== | ||
+ | |||
+ | Arduino UNOに載せるタイプで、安定して書き込みが行えます。Arduino UNOには、Arduino ISPスケッチを書き込むことで、スマイルデコーダなどのType-A準拠のDCCデコーダにファームウェアを書き込みできます。価格は1000円(部品キット)です。 | ||
+ | |||
+ | {{http:// | ||
===== 組み立て方 / How to assemble Smile Programmer ===== | ===== 組み立て方 / How to assemble Smile Programmer ===== | ||
行 8: | 行 29: | ||
Cut the red line which is RESET line between ICSP and Reset button. After that, jumper D10 and RST as the following. | Cut the red line which is RESET line between ICSP and Reset button. After that, jumper D10 and RST as the following. | ||
- | {{http:// | + | {{http:// |
- | [[http:// | + | [[http:// |
- | カードエッジコネクタを図のように曲げて差し込み、ハンダ付けします。これで終わりです。\\ | + | カードエッジコネクタを図のように曲げて差し込み、ハンダ付けします。これで終わりです。(以下の写真は、古い基板ですが、コネクタの付け方は同様です。)\\ |
Insert Card edge connector and solder it. That's all! | Insert Card edge connector and solder it. That's all! | ||
{{http:// | {{http:// | ||
[[http:// | [[http:// | ||
- | |||
- | Smile Programmer for Smile Decoder\\ | ||
- | {{http:// | ||
Programming Arduino sketch using Smile Writer\\ | Programming Arduino sketch using Smile Writer\\ | ||
行 28: | 行 46: | ||
First time, you need to set up Smile Writer as the following. This following procedure does only once at first time. | First time, you need to set up Smile Writer as the following. This following procedure does only once at first time. | ||
- | - Check Serial port connected Smile Writer. | + | - 予め、[[https:// |
- | - Run Arduino IDE. | + | - スマイルライターに接続されたシリアルポートを確認してください。もし、CH340Gのドライバをインストールしていない場合は、インストールしてください。[[http:// |
- | - Set board to Arduino nano with ATMEGA328. | + | - Arduino IDEを起動してください。\\ |
- | - Open " | + | - Arduino IDEのボード設定及びマイコン設定はArduino nanoとATMEGA328を選択してください。COMポートは認識されているボードに対応したものを選んでください。書き込み装置は、" |
- | - Upload it. | + | - ファイルメニューのスケッチの例から、" |
+ | - " | ||
+ | |||
+ | 参考: | ||
+ | Arduino nano互換ボードをAVRISPとしてスマイルデコーダの書き込みを行うことができます。Arduino ISPについては[[http:// | ||
+ | |||
+ | ===== 販売 ===== | ||
+ | |||
+ | DesktopStation、または名古屋電鉄にて販売中です。 | ||
smile_writer.txt · 最終更新: 2018/09/09 09:26 by yaasan